Small Parts

What to do when just one little part could make your installation perfect? Your local hardware store simply does not carry these items so you think you're out of luck? Here you go! Lock strike plates, iron spindles, screws, spacers and little do-dads you may want or need. If you need something that is not listed, just ask.  I probably have it.
 


Item #- Item
DSP1131 Solid Brass Strike Plate for Antique/Vintage Mortise Locks

Solid Brass Strike Plate for Antique/Vintage Mortise Locks

This is a solid brass strike plate with a nice mellow patina. Perfect for the antique hardware sold here! Reversible for right or left hand doors. Just turn it over. One side has some nicks but maybe that is not the side you need showing? 3-1/4” high x 7/8” wide excluding tongue Strike opening... click picture for more info
DSP1130 Russell & Erwin Rounded Antique Strike Plates

Russell & Erwin Rounded Antique Strike Plates

This is the only manufacturer I know of that created a lock and strike plate with a rounded top and bottom. Lots easier to create the mortise for installation and Russell & Erwin patented the design May 1, 1900 as inscribed on each strike plate. Although these strike plates are perfect for the... click picture for more info
DSP1129 Solid Brass 3/8” Entry Doorknob Spindle for Antique Mortise Lock

Solid Brass 3/8” Entry Doorknob Spindle for Antique Mortise Lock

This is a hard-to-find spindle in that it does not rotate in the middle. Made of solid brass it will give years of service since there is no chance it will break in half. Includes original set screws. Spindle is 3/8” square and 4-1/4” long.  Widest screw spacing 3-5/8" and shortest screw... click picture for more info
DSP1128 Vintage Dutch Door Quadrant - NOS

Vintage Dutch Door Quadrant - NOS

This great piece of hardware was made by Ives around 1940-1950 in New Haven, Conn – the good old USA! It has never been used (New/Old Stock) and comes in its original box. Made of cast brass hand polished with a black finish. Sorry – screws have been lost over the years but can be found at any... click picture for more info
DSP1126 Nickel Plated Strike Plate for Antique/Vintage Mortise Locks

Nickel Plated Strike Plate for Antique/Vintage Mortise Locks

This strike plate is made of strong steel with mellowed nickel plating. The plating is not as shiny as it appears in the photos. Perfect for the antique hardware sold here! Reversible for right or left hand doors. Just turn it over. 3-3/8” high x 7/8” wide excluding tongue Strike opening 1/2” wide... click picture for more info
DSP1125 Nickel Plated Strike Plate for Antique/Vintage Mortise Locks

Nickel Plated Strike Plate for Antique/Vintage Mortise Locks

This strike plate is made of strong steel with mellowed nickel plating. The plating is not as shiny as it appears in the photos. Perfect for the antique hardware sold here! Reversible for right or left hand doors. Just turn it over. 3-1/4” high x 7/8” wide excluding tongue Strike opening 1/2” wide... click picture for more info
DSP1119 Three Part Yale & Towne Spindle – Free Door Knob

Three Part Yale & Towne Spindle – Free Door Knob

These spindles are made of three separate triangular pieces that fit together to form a square.  One doorknob would be pinned to the spindle and the pin is held in place by the collar of the rosette.  I’ve included a brass door knob but you can pop the pin out and use the spindle on another knob... click picture for more info
DSP1112 Inside Closet Handles – One Nickel and One Brass – Your Choice

Inside Closet Handles – One Nickel and One Brass – Your Choice

Why waste a beautiful knob on the inside of the closet? These hold your outside knob in place and provide a method of getting out of the closet if you happen to be inside and close the door :o) They are both made of steel and one has brass plating with the other nickel. Both have mellowed with age.... click picture for more info
DSP1105 Split 1/4” Doorknob Spindle for Antique Mortise Locks

Split 1/4” Doorknob Spindle for Antique Mortise Locks

This is an iron split (or swivel) spindle that allows the doorknobs on either side of a door to turn independently.  It is used for mortise locks that have push buttons or tabs on the face of the lock.  When locked the knob on the inside will retract the strike but the knob on the exterior will... click picture for more info
DSP1103 Split 1/4” Doorknob Spindle for Antique Mortise Locks

Split 1/4” Doorknob Spindle for Antique Mortise Locks

This is an iron split spindle that allows the doorknobs on either side of a door to turn independently.  It is used for mortise locks that have push buttons or tabs on the face of the lock.  When locked the knob on the inside will retract the strike but the knob on the exterior will not.  The... click picture for more info
DSP1099 Ornate Norwalk Antique Strike Plate for Mortise Lock

Ornate Norwalk Antique Strike Plate for Mortise Lock

Norwalk produced some very Egyptian influenced hardware during the late 1800’s and this strike plate is no exception. Made of thick cast bronze the incising is still crisp and clear on both sides even after all these years. The strike/deadbolt holes have been cut sometime in the past as was... click picture for more info
DSP1087 Ornate Replacement Lock Face or Strike Plate

Ornate Replacement Lock Face or Strike Plate

This thick bronze face plate is from a late 1800’s entry mortise lock made by Kean & Doty.  Use as intended if yours is lost/broken or I have also seen them used for an ornate strike plate for the matching lock (you would have a little extra hole on top of the strike opening though).  The plate... click picture for more info
DSP1078 Ornate Corbin “Ceylon” Cast Bronze Strike Plates - Polished

Ornate Corbin “Ceylon” Cast Bronze Strike Plates - Polished

These ornate strike plates were made by P & F Corbin around the turn of the century for their Ceylon design hardware. Don’t restrict them to just Ceylon hardware though! This design will go with a multitude of mortise locks. The design is on one side only and they are reversible for right or... click picture for more info
DSP1026 Ornate Cast Brass Closet Turn Knob

Ornate Cast Brass Closet Turn Knob

In days long ago the knob inside a closet was a simple shaped grip rather than a full size doorknob but there is nothing simple about this one!  Whether you want to impress your guests as you open the coat closet or as a private joy for a bedroom closet, you’ll smile each time you open the door!... click picture for more info
DSP1015 Arts & Crafts Mortise Lock Thumb Turn Knob

Arts & Crafts Mortise Lock Thumb Turn Knob

This is a lovely brass or bronze thumb turn that could have been manufactured anywhere from 1910 – 1940.  It has a simple shapely backplate and a large knob that is knurled on the edge.  This piece can be used to throw the deadbolt on smaller mortise locks or is also appropriate with the large... click picture for more info
DSP1010 Iron 1/4" Spindle for Antique & Vintage Doorknobs

Iron 1/4" Spindle for Antique & Vintage Doorknobs

These spindles have been cleaned and all the screw holes have been tapped so that the new set screws sold here insert easily.  If you are using your own old screws you might want to request that the holes not be tapped in the Comments section at checkout.  The spindles come in various lengths but... click picture for more info
DSP1007 Skeleton Key for Antique Mortise Lock

Skeleton Key for Antique Mortise Lock

Some people like to have a skeleton key for their mortise locks and some don’t use the deadbolt function.  With this in mind I have listed several mortise locks without a skeleton key and have noted with that particular lock that you can purchase one with this Item Number.  If you want more than... click picture for more info
DSP1003 Spacers for Antique Doorknobs

Spacers for Antique Doorknobs

Although antique doorknob spindles allow for a wide variation in door thickness, sometimes a little bit more help is needed. These spacers go between the doorknob and the door plate to make the doorknobs fit more snugly. These will fit all but the tiniest antique doorknob collar. Note: These... click picture for more info
DSP1002 Set of 4 New Brass Set Screws for Antique Doorknobs

Set of 4 New Brass Set Screws for Antique Doorknobs

These new screws are #10 - 24 x 7/16" slotted oval head machine screws with a small head (.25" or 1/4" diameter). Being custom made, they fit antique knobs with countersunk screw holes correctly, and do not stick out of the knob shank like the hardware store variety. You will need to... click picture for more info

Copyright © 2015 Historic Home Hardware and Antique Doorknob Hardware. Powered by Zen Cart
Parse Time: 0.868 - Number of Queries: 241 - Query Time: 0.0550051549988